Understanding Static Pressure in Your Spray Booth
Presented by Trey Peavy
Static pressure is one of the most misunderstood variables in spray booth performance. RTT’s Trey Peavy breaks down what static pressure is — the resistance a fan faces when trying to move its designed airflow — and identifies the most common causes: 90° duct elbows, transitions, offsets, and filter loading. You’ll learn why a fan rated for 10,000 CFM at ½″ static pressure will fall short if your system generates 1″ of resistance, and why designing the full duct system around actual static pressure is critical to achieving proper airflow and finish quality.
Video Chapters
- 0:00 Introduction
- 0:18 What Is Static Pressure?
- 0:32 Whiteboard Demo
- 1:12 90° Elbows & Turbulence
- 1:47 Filters & Resistance
- 2:08 Engineering the Full System
- 2:37 Fan Performance Impact
- 3:02 Wrap-Up
Video Transcript
Hey everybody, I'm Trey Peavy with RTT Finishing Solutions. Today we want to talk about static pressure — what that means in your spray booth, your powder booth, or maybe even your cure oven.
A lot of people don't know what static pressure is. In the industry, we say it all the time. We talk about it all the time — a fan moves 10,000 CFM at a half-inch of static pressure. Maybe you don't know what that is. So today, let's talk about it.
What Is Static Pressure?
Static pressure is the resistance that the fan sees when trying to move its designed airflow.Whiteboard Demo
Let's go to the whiteboard. If we had a piece of ductwork running here and our airflow is moving this way — that's our 10,000 CFM. Right now there's nothing but a straight piece of pipe, so there's not a lot of resistance against that airflow. Static pressure is the resistance pushing perpendicular to the airflow — pushing against the walls of the duct. That pressure creates friction, which creates resistance.90° Elbows & Turbulence
Where we see the most resistance is when we turn that ductwork 90°. When that happens, the airflow coming across profiles that outside edge. The air collides with the air on the outside and creates turbulence — air spinning inside the elbow, creating resistance against the fan. The more 90° elbows you have, the more resistance you put against the fan.Filters & Resistance
Add a filter bank into the system and as those filters load up, resistance increases. Clean filters have a certain amount of resistance — dirty filters have more. There are industry standards around spray booths and certain airflow types carry certain static pressure values.Engineering the Full System
The best approach is to take the full system into account and engineer it from the start. How many elbows? How many offsets? How many transitions? What type of filtration — one stage of RP arrestors, two stages, three? All of those factors play a vital role in fan performance.Fan Performance Impact
Static pressure is a huge factor in fan performance. If a fan is designed to move 10,000 CFM at a half-inch of static pressure but sees one inch of static pressure in the system, it will not move 10,000 CFM. You're no longer moving the airflow you need. If your filters just need to be changed, you may recover performance. But when designing a system, you need to account for every factor that affects fan performance up front. I hope this quick video on static pressure was beneficial. We'll catch you in the next one.Additional Resources
Successful Spray Booth Installations
Presented by Chris Schoch
Avoid costly spray booth installation surprises. We cover the project flow from quote to install, plus real-world lessons on field conditions, ductwork, air makeup units, filtration and ovens.
Filter Grids and Installation
Presented by Cayce Carr
Learn how to install RTT exhaust filter grids and RP W Series filters, from grid sizes and part numbers to filter orientation and a positive seal.
FilterLoc and Filter Installation
Presented by Trey Peavy
Learn how RTT’s FilterLoc Track system installs in minutes, seals 100% of the filter perimeter and cuts spray booth filter labor by 60%.
Air Make Up Unit Overview
Presented by Luke Downing
Air makeup unit overview for spray booths: CT series features, heat and cure modes, recirculation, temperature and humidity control, and quoting tips.
Quoting RTT Products: What To Do First
Presented by Allan Mustard
Planning a finishing booth? Learn the seven details our team needs to size and configure your equipment and deliver an accurate quote.
Not Sure Which System You Need?
Get a system built around your application, with the right airflow, filtration, and fit for your facility.
