Exhaust Filter Pad vs. Blanket Installation

Presented by Cayce Carr and Trey Peavy

Trey Peavy and Cayce Carr from RTT Finishing Solutions time a spray booth filter change-out side by side. Four 20″ x 20″ pad filters took 2:30 to change. A blanket filter in the FilterLoc Track system took 1:32 and covers more filter area. In this video: • Removing and installing pad filters • EXF and snap-in grid options for multi-stage filtration • Centering pads for a positive seal • Installing blanket media with the FilterLoc Track system and tool • Why blanket media saves time in larger booths

Video Chapters

Hello everyone. I’m Trey Peavy, General Manager at RTT Finishing Solutions. With me is Cayce Carr, Engineering Manager at RTT.

We’re in our training room today to talk about filter change-outs. Cayce is going to change out a set of pad filters and then a blanket filter, and I’ll time each one.

For this demo, we’re pretending the filters are fully loaded with overspray. Cayce will remove them and set them on our table, which will “magically” clean them, and then he’ll reinstall them. Then we’ll move on to the blanket media.

Note that the blanket in our training room is about 32" wide, while the pad filters are 20" x 20". In a typical installation, we’d use a 45" wide blanket, which covers two cells. If we can change out these four pads and the blanket in the same amount of time, we’ve gained 50% in productivity.

Ready? Go.

Pad filter change-out

Removing a pad is simple and straightforward. It pulls right off the prongs on the filter grid. Of course, the longer grids are in service, and depending on the coating, the stickier they get. We’ve all seen them built up around the edges.

Cayce has cleaned our filters and is reinstalling them now. We have a separate video where he demonstrates proper filter grid installation and pad filter installation. We encourage you to check it out.

These are the 20" x 20" EXF grids that your booth was likely shipped with. We also sell a snap-in grid with rubber grommets on the RP side, which is ideal for multi-stage filtration. You could install a pad or bag filter in a snap-in grid, add a pad filter in front of it, and hang a blanket in front of that for three stages of filtration.

We’re at about 1:35, and Cayce is on his third filter.

When installing pads, keep them centered. The pad is larger than the opening, which gives you extra material for a positive seal. You don’t want the filter sitting low, because that’s where bypass happens. When the exhaust fan turns on, it pulls the media back into place. The more the filter loads, the more it pulls in.

He’s on his last pad now, working the top.

Picture this in a larger booth, such as a truck booth. Many people would need a scissor lift, moving back and forth and up and down to change out every cell.

He’s done, right at 2 minutes and 30 seconds.

Blanket installation

Now we’ll pull down this filter and replace it with a fresh blanket. Ready? Go.

This is our FilterLoc Track system, which comes standard on new RTT spray booths. The old filter comes out very easily.

Hang the blanket from top to bottom. Installation is the same as with a pad filter: make sure the louvers are fully open across the face. We cover this in detail in our other videos.

Cayce is using the FilterLoc tool to install the filter. Guide the filter and pull it down so you’re pulling against the stitching, at the point where it was originally manufactured to length. Then run the tool along the track.

Depending on the media, you may need to adjust the pressure on the tool. A W Series filter has multiple layers of paper and a high-density polyester backing, so it takes a little more work than a W 50 or one of our legacy products, such as the 3031 or 3200.

He’s done. I’m stopping the clock.

We have some excess material from cutting the filter to this opening size. It doesn’t need to be tucked in or trimmed. When the filter is pulled out, the excess helps protect the FilterLoc Track. With multiple blankets installed side by side, they butt up against each other, and the excess material fully protects the track.

Results

  • Four pad filters: 2 minutes, 30 seconds
  • One blanket: 1 minute, 32 seconds

And if this blanket were 45" wide, it would have covered two cells, giving you much more filter area in less time. Matching that with pads would take about 5 minutes, versus about 2 minutes with the blanket.

That’s what we wanted to demonstrate. Great job, Cayce. Check out our other videos, and thanks for watching.



Additional Resources

Not Sure Which System You Need?

Get a system built around your application, with the right airflow, filtration, and fit for your facility.

Request A Quote

With over 75 years of combined experience engineering complex, multi-component finishing solutions, our team has the expertise to design and build equipment for projects of any scale — tailored precisely to your specifications.

 

Share a few details below and we’ll have a proposal back to you within 24 hours.