Monitor Part Temperature with Smartbatch
Presented by Bryan Willis
Powder cures at part temperature, not air temperature. Bryan Willis, Controls Manager at RTT Finishing Solutions, shows how SmartBatch technology monitors up to four part thermocouples in real time, starts the cure timer automatically when parts reach temperature, and records every cycle. That gives your QC team proof that each batch was cured correctly.
Video Chapters
- 0:00 Introduction
- 0:13 How SmartBatch works
- 0:35 Standard batch ovens vs. SmartBatch
- 1:16 Real-time part temperature monitoring
- 1:48 Automatic cure timer
- 2:24 Data recording and reporting
- 2:53 Quality control
Video Transcript
Hi, I’m Bryan Willis, Controls Manager at RTT Finishing Solutions. In this video, we’ll cover the benefits of SmartBatch technology, available on our batch ovens.
How SmartBatch works
SmartBatch is patent-pending technology. It uses thermocouples attached to the individual parts inside the oven. The thermocouples connect to a junction box inside the oven, and the junction box is wired to the control panel. That means no wires running across the floor and under the door, where they could get damaged over time.
Standard batch ovens vs. SmartBatch
A standard batch oven has one thermocouple, usually in the roof, that measures air temperature. That works, and it gives the oven a single data point to operate from. You can then make adjustments based on information from a separate recording device.
The problem with a separate recording device is the process. You load the oven, attach the thermocouples, start the oven, wait for the full cycle to run and cool down, and only then pull out the data. If the results aren’t right, you start over. That wastes at least one batch, maybe two.
With SmartBatch, you see that information in real time.
Real-time part temperature monitoring
Say you have parts of different thicknesses in the oven, such as an I-beam, a steel plate and a much thinner panel. You can attach up to four sensors across those parts.
Start the batch and set the temperature. The touchscreen displays the actual part temperatures in real time, so you can make adjustments as needed.
Automatic cure timer
Once the process is dialed in, the timer can start automatically when the parts reach the target temperature.
Powder coatings cure at a specific part temperature, so air temperature isn’t what matters to the part. That’s where SmartBatch is most useful. When the parts reach temperature, the oven starts the timer and runs only the minimum time required to cure. Then it shuts off the burner and lets the oven cool.
Data recording and reporting
All of this data can be viewed in real time and is also recorded. You get a graph plus data points in an Excel-style format. You can export them from the screen to a USB drive, or have them emailed automatically at the end of each cycle. Emails notify your phone and can also be opened in our SmartConnect app, a standard feature on SmartBatch ovens.
Quality control
Your QC department can use these graphs to confirm the parts actually reached temperature. If a finish problem comes up, you can rule out the oven, because you know the parts reached temperature for the required time. Then you can look at other areas, such as pretreatment or application.
I hope this video helps explain SmartBatch technology. Thanks for watching, and stay safe.
Additional Resources
Spray Booth Recipe Setup
Presented by Bryan Willis
Learn how to program a cure recipe on your spray booth AMU control panel, including spray, flash, cure and cool set points, saving your changes and activating the recipe before curing.
Spray Booth Sizing and Selection
Presented by John Owed
A practical guide to spray booth sizing and selection: why booths are required, how to calculate airflow, when to choose crossdraft or downdraft, and which upgrades improve performance.
Proper Use and Measurement of a Manometer
Presented by Cayce Carr and Trey Peavy
A step-by-step guide to installing the Dwyer Mark II manometer on your spray booth exhaust chamber: mounting, leveling, filling with gauge fluid, zeroing and connecting the pressure ports.
Spray Booth Inspection for Compliance
Presented by John Owed
Avoid costly spray booth citations. Discover common compliance issues, including blocked manometers, missing fire suppression, unsafe spray areas and poor shop housekeeping.
Download Reports from SmartTouch Control Panels
Presented by Bryan Willis
Bryan Willis shows how to export temperature history from an RTT SmartTouch control panel to a USB thumb drive, then open the saved data log as Excel spreadsheets on your computer.
Successful Spray Booth Installations
Presented by Chris Schoch
Avoid costly spray booth installation surprises. We cover the project flow from quote to install, plus real-world lessons on field conditions, ductwork, air makeup units, filtration and ovens.
Not Sure Which System You Need?
Get a system built around your application, with the right airflow, filtration, and fit for your facility.
